Scale Calculator
The distance between the frets of a scale is obtained by dividing the string length by the proportionality factor ¹²√2 = 1.059463. Enter your instrument's string length and number of frets to calculate the exact position of each fret.
| Fret number | Fret-to-fret distance (mm) | Distance from nut to fret (mm) | Distance from nut to fret (cm) |
|---|
How the calculation works
Here's an example calculation for a 650mm string length:
650 / 1.059463 = 613.51835 650 – 613.51835 = 36.48 (fret 1) 613.51835 / 1.059463 = 579.08426 613.51835 – 579.08426 = 34.43 (fret 2) 579.08426 / 1.059463 = 546.5828 579.08426 – 546.5828 = 32.50 (fret 3)
The process repeats for the desired number of frets, always using the remaining length from the previous fret as the new base for the calculation.
Ready-made reference tables
Pre-calculated values for the two most common scales, from fret 1 to fret 19. For any other measurement, use the calculator above.
Classical guitar (650 mm)
| Fret number | Fret-to-fret distance (mm) | Distance from nut to fret (mm) | Distance from nut to fret (cm) |
|---|---|---|---|
| 1 | 36.482 | 36.482 | 3.648 |
| 2 | 34.434 | 70.916 | 7.092 |
| 3 | 32.501 | 103.417 | 10.342 |
| 4 | 30.677 | 134.094 | 13.409 |
| 5 | 28.956 | 163.050 | 16.305 |
| 6 | 27.330 | 190.380 | 19.038 |
| 7 | 25.796 | 216.177 | 21.618 |
| 8 | 24.349 | 240.525 | 24.053 |
| 9 | 22.982 | 263.507 | 26.351 |
| 10 | 21.692 | 285.200 | 28.520 |
| 11 | 20.475 | 305.674 | 30.567 |
| 12 | 19.325 | 325.000 | 32.500 |
| 13 | 18.241 | 343.240 | 34.324 |
| 14 | 17.217 | 360.458 | 36.046 |
| 15 | 16.251 | 376.708 | 37.671 |
| 16 | 15.339 | 392.047 | 39.205 |
| 17 | 14.478 | 406.525 | 40.652 |
| 18 | 13.665 | 420.190 | 42.019 |
| 19 | 12.898 | 433.088 | 43.309 |
Cavaquinho (340 mm)
| Fret number | Fret-to-fret distance (mm) | Distance from nut to fret (mm) | Distance from nut to fret (cm) |
|---|---|---|---|
| 1 | 19.083 | 19.083 | 1.908 |
| 2 | 18.012 | 37.094 | 3.709 |
| 3 | 17.001 | 54.095 | 5.410 |
| 4 | 16.047 | 70.142 | 7.014 |
| 5 | 15.146 | 85.288 | 8.529 |
| 6 | 14.296 | 99.584 | 9.958 |
| 7 | 13.494 | 113.077 | 11.308 |
| 8 | 12.736 | 125.813 | 12.581 |
| 9 | 12.021 | 137.835 | 13.783 |
| 10 | 11.347 | 149.181 | 14.918 |
| 11 | 10.710 | 159.891 | 15.989 |
| 12 | 10.109 | 170.000 | 17.000 |
| 13 | 9.541 | 179.541 | 17.954 |
| 14 | 9.006 | 188.547 | 18.855 |
| 15 | 8.500 | 197.047 | 19.705 |
| 16 | 8.023 | 205.071 | 20.507 |
| 17 | 7.573 | 212.644 | 21.264 |
| 18 | 7.148 | 219.792 | 21.979 |
| 19 | 6.747 | 226.538 | 22.654 |
Intonation
This section summarizes the article “Intonation”, by Paul Jacobson (Hand-Crafted Guitars), originally published in Guitar Review (Summer 1990) and later revised. Full text: archived version of the article.
Classical guitars struggle to stay in tune because nylon is unstable, but many intonation problems come from the instrument's construction. Almost any guitar in playable condition can reach very good intonation. The first thing to check is fret spacing: it follows the constant 17.817, so the first fret sits at 1/17.817 of the scale length, and the 12th fret falls exactly at half the scale.
Once the frets are right, the main factor is string stretch when a note is fretted. The string gets longer and tighter, and the note goes sharp. Each string reacts differently, following three rules: sharpening is inversely proportional to pitch (the pitch rule); pitch is proportional to tension (the tension rule); and tension is proportional to string mass (the mass rule). That is why the D string sharps less than the G string, even though it is lower.
Compensation adjusts the length of each string separately, at two points. At the bridge (saddle), the saddle is set back to compensate for travel stretch, the part of the stretch that happens as the string reaches the fret crown. At the nut, the break-off point is moved forward to compensate for fretting stretch, the extra stretch caused by pressing the string behind the fret. The bridge is adjusted first, because fretting stretch always follows travel stretch.
Reference values (the author's empirical compensation)
| String | Saddle setback (mm) | Nut setforward |
|---|---|---|
| Et (treble E) | 1.00 | < 1/64" (< 0.40 mm) |
| B | 1.50 | 1/64" (≈ 0.40 mm) |
| G | 2.25 | 1/32" (≈ 0.79 mm) |
| D | 1.75 | 1/64" (≈ 0.40 mm) |
| A | 2.00 | 1/64" (≈ 0.40 mm) |
| Eb (bass E) | 2.50 | 1/64" (≈ 0.40 mm) |
Worked example 1: saddle position for a 650 mm scale
The saddle setback is added to the nominal scale length, measured from the nut to the string's contact point on the saddle. For the G string: 650 mm + 2.25 mm = 652.25 mm. The nut setforward is converted from inches: 1/32" = 0.79 mm and 1/64" = 0.40 mm.
| String | Saddle from nut (mm) | Nut setforward (mm) |
|---|---|---|
| Et | 651.00 | < 0.40 |
| B | 651.50 | 0.40 |
| G | 652.25 | 0.79 |
| D | 651.75 | 0.40 |
| A | 652.00 | 0.40 |
| Eb | 652.50 | 0.40 |
Worked example 2: checking the saddle with the 12th fret
With a 650 mm scale, the 12th fret sits at 650 / 2 = 325.00 mm from the nut. To check the saddle, fret the string with a small wooden dowel pressed against the fret crown, so only travel stretch is applied. The saddle is correct when the note fretted at the 12th fret is exactly one octave above the open string, which is the same as the 12th-fret harmonic. Use a strobe tuner or your ear. The 12th fret is the reference because the harmonic and the fretted note are theoretically equal only there.
The values were measured with D'Addario J45 strings, on the author's guitars with a double-twist fingerboard. They are not universal: each instrument must be evaluated individually.
Test compensation on fully stretched strings. Right after restringing, the guitar sounds slightly flat, especially in higher positions.
The author himself advises against changing the nut without experience, because a proper nut compensation requires shortening the fingerboard and making a new nut.